General Panda Parts Request

[lukmek]

OMFG; you beauty! Again, I'll have one for each side. Again, let me know if you need it to be through you, or you prefer me going direct.

Mate, you are a star.:worship:

You need both front & rear panels dx and sx?

 

[lukmek]

Vintage Mudflap original fiat ricambio

 

[panda1408]

Thanks firstcar-Y10 and lukmek. Those are it! luk would you be able to send a message asking who the manufacturer is?

 

[lukmek]

Thanks firstcar-Y10 and lukmek. Those are it! luk would you be able to send a message asking who the manufacturer is?

I sent the message to the seller
Will let you know

 

[Sjvarley]

lukmek, Thanks for looking, however those are the plastic inner arch guards, I am after the actual steel wheel arch panel. Like the one Sjvarley linked to, however that is a mk1, I need a mk2.

Freddy do you still
Need a panel I am going to the auto demolition in belluno Italy this week how much of a section do you need and could you wait until the 15 th April
Doors and tail gate for the (BFP Brian) on the list too !

 

[ChrisnCareyAnn]

You need both front & rear panels dx and sx?

I'm ok for the front. It was rear nearside and rear offside I was hoping for, ta.
"dx" and "sx" are left and right are they? Forgive my ignorance.

 

[ChrisnCareyAnn]

Chris
Gimme a list of all the parts you want and I see if I can get a discount on shipping first!
Some shop won't send worldwide I can ask them to send the order to my address in Rome or London and then forward it to you

Fingers crossed it's now just two rear body panels and the inners, that you have shown.
Of course, when my new Sisley arrives on wed/thurs; Heaven only knows what will come from that!
Thanks mate.
Chris

 

[panda1408]

Freddy do you still
Need a panel I am going to the auto demolition in belluno Italy this week how much of a section do you need and could you wait until the 15 th April
Doors and tail gate for the (BFP Brian) on the list too !

Yes I still need an arch panel and yes I can wait until April! I need the complete flared section of the right hand rear arch, probably best to cut the bottom half of the quarter out I would think, although I don't need the sill section. I also need the top of the windscreen frame/front of roof, I asked Adam if your donor shell is any good in that area, he was going to have a look.

We can come to an agreement with the propshaft bits if you could get me the panel, your help would be very much appreciated!:worship:

 

[Sjvarley]

Ok mate I know the shell st home is fine at the top of the window. It's a chance that a whole shell is in good condition here too but I can let u know the out come by Friday
Regards sj

 

[lukmek]

I sent the message to the seller
Will let you know

Sorry
Still waiting for a reply from seller

 

[lukmek]

I'm ok for the front. It was rear nearside and rear offside I was hoping for, ta.

"dx" and "sx" are left and right are they? Forgive my ignorance.

Yep
Right & left
Do you still want me to ask for the 2 panels and postage cost?
Thanks

 

[ChrisnCareyAnn]

Yep
Right & left
Do you still want me to ask for the 2 panels and postage cost?
Thanks

Absolutely, yes please M8...Makes me wish I had stuck with the Italian course me and her-indoors did 20 years ago!
Chris:bang:

 

[Sjvarley]

Yeah, absolutely. I've seen your thread and you are an absolute monster for this stuff, mate. If I am stuck on a desert island with nothing but metal and metalworking equipment to hand, I want you there as well :worship:

I was going to make a couple if I can't find any nos...trouble is I'm a chippy, so they'll be carved from elm...sigh...

Seriously, though, if nothing appears before I fit the new brake pipes, I'll be having a go at fabricating something... Given my skill set rests in boatbuilding, there is also the possibility of using the steel ones as a mould to make them out of glassfibre... hmm.

But thanks for the tip, mate.

Chris

You know you've got the skill if your. A chippy ,just need different drill bits and jigsaw bits it's all the same really Tape measure Dividers , cut drill hammer Spanner [emoji1009][emoji375][emoji1360][emoji209][emoji3]

 

[ChrisnCareyAnn]

You know you've got the skill if your. A chippy ,just need different drill bits and jigsaw bits it's all the same really Tape measure Dividers , cut drill hammer Spanner [emoji1009][emoji375][emoji1360][emoji209][emoji3]

True dat. And to be honest, I did a lot of stainless trim fettling working on the Yachts, so I can cut , grind, polish and spanner ok, just the welding needs to be learned. Did a bit of stick welding many moons ago, working on tractors and trailers, but that stuff was so thick, penetration was the main issue! Going to look see if there's a night class in TIG/MIG, locally.:idea:

 

[lukmek]

Absolutely, yes please M8...Makes me wish I had stuck with the Italian course me and her-indoors did 20 years ago!

Chris:bang:

Hi Chris
Please PM me the list of parts and I will try to make a deal with the seller for shipping to U.K.
I then will order for you because the order can only be sent to the registered card address
I will forward the parcel to you when I get it
Otherwise I can give you details for you to contact the seller and place the order if you could get it sorted in Italian
They are based in south Italy
Cheers
Ciao
Luca

 

[lukmek]

Hi Chris
Sent you PM
[emoji106]

 

[lukmek]

onemanmade



Try to locate some fabric for you
Could you please post some pics of your interiors
[emoji1360]

 

[P1NKY]

lukmek, can you still get the original fiat linea accessori 3rd brake light?

 

[lukmek]

lukmek, can you still get the original fiat linea accessori 3rd brake light?

I am looking for one for you
pretty sure it will be second hand if its ok with you
on mine I have changed the 10 filament light bulbs with Led bulbs as well

 

[P1NKY]

I am looking for one for you
pretty sure it will be second hand if its ok with you
on mine I have changed the 10 filament light bulbs with Led bulbs as well